HOW TO DISASSEMBLE PHILIPS HD8751 SAECO INTELIA BREW GROUP

YOU NEED TO PREPARE THIS TOOL FIRST. 'HEXA SCREW DRIVER'

MOST OF THE SCREW BOLTS ARE HEXA TYPE.

 

 

SYNTHETIC GREASE. I BOUGHT A CAN TYPE ONE AND IT'S LIKELY TO USE UNTIL THE END OF MY LIFE :)

 

 

TAKE OFF THE BREW GROUP FROM THE MACHINE AND UNSCREW THESE TWO BOLTS FIRST.

 

 

IT'S VERY SIMPLE AND EASY. LOOSEN THOSE TWO BOLTS AND THEN TAKE OFF THAT THING WITH GREEN SPOT FROM THE GROUP. THERE IS AN O-RING INSIDE THAT THING SO YOU NEED TO PULL THAT PART WITH LITTLE BIT STRENGTH.

 

 

AFTER PULLING OFF UPPER PART, NOW YOU NEED TO PULL OFF THAT PART WITH A RED O-RING THING. THIS TIME, PRESS UNDER THE TOP WHILE PUSHING THOSE CLASP THING OUT EACH SIDE IN TURN.

 

 

 

NOW YOU CAN DISASSEMBLE THOSE TOP THINGS.

 

 

YOU CAN FIND A SPRING AND A PLASTIC BALL AND A SPRING IS LITTLE BIT DIFFERENT FROM NORMAL SPRING. THE UNDER PART OF THE SPRING IS NARROWER THAN TOP. SO YOU SHOULD PUT THAT SPRING EXACTLY WHEN ASSEMBLYING. BE CAREFULL NOT TO GET LOST THAT SPRING AND ESPECIALLY THAT TINY BALL!!!

 

 

IF YOU TAKE OFF THAT CIRCULAR STAINLESS NET, YOU CAN FIND COFFEE BEAN DREG INSIDE. CLAEN IT ALL.

 

 

EVEN THOUGH I HAVE USED A TABLET CLEANER EVERY 500 SHOTS AND HAVE SCALED A BOILER AND WATER LINE 6TIMES UNTIL NOW SINCE JULY 2014, IT WAS PRETTY DIRTY.

 

 

WASHED THE UPPER PART

 

 

NOW UNSCREW THAT BOLT UPPER THE 'PUSH'LETTERS.

 

 

 

PULL OUT THAT SPRING WITH SMALL PART AND THEN UNSCREW 4 BOLTS OF THE BREW GROUP BODY.

 

 

UNSCREW THIS BOLT FIRST.

 

 

AFTER LOOSENING THAT BOLT, USE A  - TYPE DRIVER AND PUT UP THE HOOK THING WITH PULLING OUT THAT PART. BEFORE DISASSEMBLING BREW GROUP, YOU SHOULD PULL OUT THAT THING. IF YOU DON'T, YOU CANNOT OPEN AN EACH SIDE COVER OF THE BREW GROUP.

 

 

THIS IS THE INSIDE PART OF BREW GROUP. NOW YOU PULL OFF THAT PART STICK WITH MUCH GREASE. PUT THAT WHOLE THING BETWEEN YOUR BOTH LAPS AND SET TIGHT NOT TO MOVE, THEN PULL OFF THAT STICKY THING.

 

 

 

OPEND BOTH SIDE COVERS AND PULLED OFF SEVERAL THINGS. IF YOU PULL OFF STICKY THING, YOU CAN PULL OUT THE PISTON THING FROM THE CORE BODY.

 

 

THERE ARE MUCH DREGS INSIDE THAT CYLINDER. WASH WITH CLEANSER AND SMOOTH BRUSH.

 

 

A PISTON WAS DIRTY ALSO WITH DREGS. CLEAN IT ALL.

 

 

AFTER CLEANING.

 

 

AFTER CLEANING. (YOU DON'T NEED TO PULL OFF THAT SPRING. JUST USE A SMOOTH BRUSH.)

 

 

AFTER CLEANING, ASSEMBLE BACK EVERY PARTS. NOW LUBRICATE MOVING LINE OF EACH COVER.

 

 

USE A COTTON STICK.

 

 

I CLEANED ALL COFFEE BEAN DREGS. VERY GOOD CONDITION NOW LIKE NEW ONE.

 

 

VERY GOOD.

 

AFTER THIS WORK, IT SEEMS TO ME THAT THE COFFEE TASTE RECOVERED LIKE BEFORE.

OF COURSE, I COULD HAVE MANAGED THE MACHINE JUST WITH DISCALE WATER AND OIL REMOVER ETC BUT IF I DIDN'T, I SHOULD HAVE SEEN THOSE COFFEE DREGS EVERY CORNER OF THE GROUP EVERY TIME I WASH BREW GROUP. RETURNED TASTE WAS AN EXTRA :)